[AYUDA] problema con speedy y un router

Hacé el test que tiene incluído y posteá el screenshot/resultado, si no, es medio complicado.
Slds.

NO se si es esta, espero que sirva

hola joaquinherrada
ese es todo el test completo??
porque me parece que te falta el del " circuito 1 ".
clickea en " Help " de la linea donde dice " Test PPPoPVC 0 PPOE connection " y postealo a ver que dice.
seguro que cuando lo configuraste lo pusiste en VC1????

Fijate si en el menú WAN tenés Bridge=NO; encapsulation=PPPoE; multiplexing=LLC
En el Virtual Circuit que tenés habilitado tenés que tener VPI/VCI=8/35 para zona Telefónica y 0/33 para zona Telecom.
Slds.
Edit: Como dice Atheo: el VC1 habilitado y el resto NO.

Este es el log, no entiendo mucho a que se refieren con vc1 activado y el resto no, `pero les dejo una pantalla de la configuracion

01/01/1970 01:37:17> PPP1 PPPoE PADI Sent
01/01/1970 01:37:17> ATM Tx Error Count: 0, Rx Error Count: 0
01/01/1970 01:37:17> u/s total bit capacity: 54bits, used: 54bits
01/01/1970 01:37:17> d/s total bit capacity: 2541bits, used: 160bits
01/01/1970 01:37:17> d/s Latency: N/A, u/s Latency: N/A
01/01/1970 01:37:17> d/s Data Rate: 608kbps, u/s Data Rate: 128kbps
01/01/1970 01:37:17> d/s Attenuation: 21.7dB, u/s Attenuation: 13.0dB
01/01/1970 01:37:17> d/s SNR: -9.0dB, u/s SNR: 31.0dB
01/01/1970 01:37:17> CO Vendor: ALCATEL_NETWORK
01/01/1970 01:37:17> Max Tx Power: -38dBm/Hz
01/01/1970 01:37:17> Annex Mode: ANNEX_A
01/01/1970 01:37:17> Modulation: N/A
01/01/1970 01:37:17> ADSL connected
01/01/1970 01:37:17> ATM layer is up, cell delineation achieved
01/01/1970 01:37:17> ATM Connected
01/01/1970 01:37:11> ADSL detected
01/01/1970 01:09:46> PPP1 PPPoE Session is terminated.
01/01/1970 01:09:46> ADSL disconnected
01/01/1970 01:09:46> ATM Disconnected
01/01/1970 01:01:41> PPP1 PPPoE PADI Sent
01/01/1970 01:01:41> ATM Tx Error Count: 0, Rx Error Count: 0
01/01/1970 01:01:41> u/s total bit capacity: 54bits, used: 54bits
01/01/1970 01:01:41> d/s total bit capacity: 2495bits, used: 160bits
01/01/1970 01:01:41> d/s Latency: FAST, u/s Latency: FAST
01/01/1970 01:01:41> d/s Data Rate: 608kbps, u/s Data Rate: 128kbps
01/01/1970 01:01:41> d/s Attenuation: 21.7dB, u/s Attenuation: 13.0dB
01/01/1970 01:01:41> d/s SNR: 39.6dB, u/s SNR: 31.0dB
01/01/1970 01:01:41> CO Vendor: ALCATEL_NETWORK
01/01/1970 01:01:41> Max Tx Power: -38dBm/Hz
01/01/1970 01:01:41> Annex Mode: ANNEX_A
01/01/1970 01:01:41> Modulation: G.dmt
01/01/1970 01:01:41> ADSL connected
01/01/1970 01:01:41> ATM layer is up, cell delineation achieved
01/01/1970 01:01:41> ATM Connected
01/01/1970 01:01:34> ADSL detected
01/01/1970 00:08:17> PPP1 PPPoE Session is terminated.
01/01/1970 00:08:17> ADSL disconnected
01/01/1970 00:08:17> ATM Disconnected
01/01/1970 00:00:22> PPP1 PPPoE PADI Sent
01/01/1970 00:00:22> ATM Tx Error Count: 0, Rx Error Count: 0
01/01/1970 00:00:22> u/s total bit capacity: 54bits, used: 54bits
01/01/1970 00:00:22> d/s total bit capacity: 2521bits, used: 160bits
01/01/1970 00:00:22> d/s Latency: FAST, u/s Latency: FAST
01/01/1970 00:00:22> d/s Data Rate: 608kbps, u/s Data Rate: 128kbps
01/01/1970 00:00:22> d/s Attenuation: 21.6dB, u/s Attenuation: 13.0dB
01/01/1970 00:00:22> d/s SNR: 37.1dB, u/s SNR: 31.0dB
01/01/1970 00:00:22> CO Vendor: ALCATEL_NETWORK
01/01/1970 00:00:22> Max Tx Power: -38dBm/Hz
01/01/1970 00:00:22> Annex Mode: ANNEX_A
01/01/1970 00:00:22> Modulation: G.dmt
01/01/1970 00:00:22> ADSL connected
01/01/1970 00:00:22> ATM layer is up, cell delineation achieved
01/01/1970 00:00:22> ATM Connected
01/01/1970 00:00:06> Firewall is enabled.
01/01/1970 00:00:06> Firewall is loaded.
01/01/1970 00:00:06> CfgMgr: 'Fwbsd.dlz' module loaded.
01/01/1970 00:00:06> CfgMgr: 'Prism.dlz' module loading failed.
01/01/1970 00:00:06> CfgMgr: 'Washer.dlz' module loaded.
01/01/1970 00:00:00> CfgMgr: 'Shtm.dlz' module loaded.
01/01/1970 00:00:00> ZDev device loaded OK.
01/01/1970 00:00:00> Initialized Dynamic NAPT.
01/01/1970 00:00:00> ATM: Setting up vcc0, VPI=0, VCI=35
01/01/1970 00:00:00> ATM: Detected
01/01/1970 00:00:00> Ethernet Device 0 Detected

Este es el log, no entiendo mucho a que se refieren con vc1 activado y el resto no, `pero les dejo una pantalla de la configuracion

01/01/1970 01:37:17> PPP1 PPPoE PADI Sent
01/01/1970 01:37:17> ATM Tx Error Count: 0, Rx Error Count: 0
01/01/1970 01:37:17> u/s total bit capacity: 54bits, used: 54bits
01/01/1970 01:37:17> d/s total bit capacity: 2541bits, used: 160bits
01/01/1970 01:37:17> d/s Latency: N/A, u/s Latency: N/A
01/01/1970 01:37:17> d/s Data Rate: 608kbps, u/s Data Rate: 128kbps
01/01/1970 01:37:17> d/s Attenuation: 21.7dB, u/s Attenuation: 13.0dB
01/01/1970 01:37:17> d/s SNR: -9.0dB, u/s SNR: 31.0dB
01/01/1970 01:37:17> CO Vendor: ALCATEL_NETWORK
01/01/1970 01:37:17> Max Tx Power: -38dBm/Hz
01/01/1970 01:37:17> Annex Mode: ANNEX_A
01/01/1970 01:37:17> Modulation: N/A
01/01/1970 01:37:17> ADSL connected
01/01/1970 01:37:17> ATM layer is up, cell delineation achieved
01/01/1970 01:37:17> ATM Connected
01/01/1970 01:37:11> ADSL detected
01/01/1970 01:09:46> PPP1 PPPoE Session is terminated.
01/01/1970 01:09:46> ADSL disconnected
01/01/1970 01:09:46> ATM Disconnected
01/01/1970 01:01:41> PPP1 PPPoE PADI Sent
01/01/1970 01:01:41> ATM Tx Error Count: 0, Rx Error Count: 0
01/01/1970 01:01:41> u/s total bit capacity: 54bits, used: 54bits
01/01/1970 01:01:41> d/s total bit capacity: 2495bits, used: 160bits
01/01/1970 01:01:41> d/s Latency: FAST, u/s Latency: FAST
01/01/1970 01:01:41> d/s Data Rate: 608kbps, u/s Data Rate: 128kbps
01/01/1970 01:01:41> d/s Attenuation: 21.7dB, u/s Attenuation: 13.0dB
01/01/1970 01:01:41> d/s SNR: 39.6dB, u/s SNR: 31.0dB
01/01/1970 01:01:41> CO Vendor: ALCATEL_NETWORK
01/01/1970 01:01:41> Max Tx Power: -38dBm/Hz
01/01/1970 01:01:41> Annex Mode: ANNEX_A
01/01/1970 01:01:41> Modulation: G.dmt
01/01/1970 01:01:41> ADSL connected
01/01/1970 01:01:41> ATM layer is up, cell delineation achieved
01/01/1970 01:01:41> ATM Connected
01/01/1970 01:01:34> ADSL detected
01/01/1970 00:08:17> PPP1 PPPoE Session is terminated.
01/01/1970 00:08:17> ADSL disconnected
01/01/1970 00:08:17> ATM Disconnected
01/01/1970 00:00:22> PPP1 PPPoE PADI Sent
01/01/1970 00:00:22> ATM Tx Error Count: 0, Rx Error Count: 0
01/01/1970 00:00:22> u/s total bit capacity: 54bits, used: 54bits
01/01/1970 00:00:22> d/s total bit capacity: 2521bits, used: 160bits
01/01/1970 00:00:22> d/s Latency: FAST, u/s Latency: FAST
01/01/1970 00:00:22> d/s Data Rate: 608kbps, u/s Data Rate: 128kbps
01/01/1970 00:00:22> d/s Attenuation: 21.6dB, u/s Attenuation: 13.0dB
01/01/1970 00:00:22> d/s SNR: 37.1dB, u/s SNR: 31.0dB
01/01/1970 00:00:22> CO Vendor: ALCATEL_NETWORK
01/01/1970 00:00:22> Max Tx Power: -38dBm/Hz
01/01/1970 00:00:22> Annex Mode: ANNEX_A
01/01/1970 00:00:22> Modulation: G.dmt
01/01/1970 00:00:22> ADSL connected
01/01/1970 00:00:22> ATM layer is up, cell delineation achieved
01/01/1970 00:00:22> ATM Connected
01/01/1970 00:00:06> Firewall is enabled.
01/01/1970 00:00:06> Firewall is loaded.
01/01/1970 00:00:06> CfgMgr: 'Fwbsd.dlz' module loaded.
01/01/1970 00:00:06> CfgMgr: 'Prism.dlz' module loading failed.
01/01/1970 00:00:06> CfgMgr: 'Washer.dlz' module loaded.
01/01/1970 00:00:00> CfgMgr: 'Shtm.dlz' module loaded.
01/01/1970 00:00:00> ZDev device loaded OK.
01/01/1970 00:00:00> Initialized Dynamic NAPT.
01/01/1970 00:00:00> ATM: Setting up vcc0, VPI=0, VCI=35
01/01/1970 00:00:00> ATM: Detected
01/01/1970 00:00:00> Ethernet Device 0 Detected

Tenés mal VPI/VCI. Tiene que ser 0/33 para zona Telecom u 8/35 para zona Telefónica. No puede ser 0/35

asi es como lo tenes configurado???
te falta poner donde dice " virtual circuit " 1
" bridge " como te dijo oGalati ponelo en " disable ".
" encapsulation " ponele " pppoe LLC "
le cambias la ip del router??
acordate despues si pones ips estaticas en tus compus de que la puerta de enlace y dns son este ip " 192.168.242.101 ".

tiene razon oGalati con los VPI/VCI